夹式送料机的用途
GS-906N简易操作顺序及说明

1． 材料线设定： 送料机/夹式送料机

固定座置放材料，手动阀On (No.1)夹住材料，材料下缘与模具同高或略高0-0.1mm.
2.送料时间设定
冲床：355°，送料机：送料至0（按冲床运转方向，转动皮带轮，把副尺移却至本尺0对齐）。
3.调整料厚：送料机/夹式送料机

A．送料机之设定：手动阀Off(No.2),料厚指示环向左旋转旋紧之0为0.
B.人工调整：（1）.移动座于上死点（0°），手动阀On（No.1）,材料松紧之间，向左旋0.05mm并固定之。
（2）.固定座于上死点（180°）不放松，手动阀On（No.1）,材料松紧之间，向左旋0.05mm并固定之。
4.送距调整：
A.冲床时间：90°（送料终点。送料机/夹式送料机

B.松开M16螺母，以T型扳手调整至所需尺寸，并固定M16螺母。注：送距不稳定时，请留意送距调整螺丝固定环是否松动。
5.放松点设定：
A.时机：送料完成后，遵梢定位于材料。 送料机/夹式送料机

B.松开放松凸轮之M8螺丝，调整放松线使其对准放松点，固定M8螺丝即可。

GS-1006 simple sequence of opeations and description送料机/夹式送料机
1. Material line set
Place materials in holder, manual valve On (No.1) grip material, make material bottom align with the mold or slightly higher than 0-0.1mm

2 feeding time setting
When power press is 355 °, Feeding: Feeding to 0 (in the direction of press operation, turn the pulley, the deputy ruler has moved to align the scale 0).

3 Adjust material thickness
A. Feeder of the setting: Manual Valve Off (No.2), Counterclockwise rotate indicator ring of mterial thickness to “0”. 夹式送料机的用途
B. manual adjustments:
(1) Move the seat at the top position (0 °), manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.
(2) bracket at top position (180 °) and do not relax, manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.
4. Feeding pitch adjustment:送料机/夹式送料机
A. Press Time: 90 ° (feed end).
B. Loosen the M16 nut with T-wrench to adjust to the setting length, and fix M16 nut. Note: If the feeding pitch is unstable, please pay attention to adjustable screw loose or not.

5. Loose settings:送料机/夹式送料机
A. time: when finish feeding, follow pin in the material.
B. Loosen the screws M8 cam, adjust the line so it is on relax, fixation M8 screws.

型式
Feed Model

制造号码
Serial No.:

材料宽度
Material width

放松角度
Pilot release
可调整Adjustable

材料厚度
Material thickness

送料机械
Feed Mechanism
曲轴传动
Crankshaftdrive

送料长度
Feed length

安装位置
Installation location
左边
Left of press

送料角度
Feed angle

送料方向
Feed direction
左-右
L--R